Haier Washer HWM80 0626S User Manual

Twin-tub Washing Machine  
User's manual  
This manual is for  
HWM80-0626S  
HWM80-0626SH  
Please read this manual  
carefully before using.  
Retain it for future reference.  
0030807884  
 
Names of the parts  
Wash tub cover  
Drain selector  
Program selector  
Wash timer  
Outer cover of the spin tub  
Inner cover of the spin tub  
Spin timer  
Control panel seat  
Water-filling entrance  
Control panel  
Plate support(right)  
Spin tub frame  
Spin tub  
Plate support (left)  
Water filling control handle  
Bypass channel  
Front door  
Power cord  
Water level adjust lever  
Overflow filter  
Lint filter  
Pulsator  
Drain hose  
Cabinet handle  
Wash tub  
Cabinet  
Base frame  
Notes: All illustrations in this Manual are given for reference only. Your products and  
accessories may show differences from these illustrations due to our  
continuous improvement.  
Meaning and description of the symbols  
Contents marked with that symbol are related  
Warning sign  
to the safety of the product and the personal  
safety of the users. Please operate in strict  
conformity to the contents, otherwise it may  
cause damage of the machine or injure the  
personal safety of the user.  
Contents marked with that symbol are actions  
Forbidding sign  
forbidden to perform. Performing of those  
actions may result in damage of the machine  
or injure the personal safety of he user.  
Please check if the power receptacle has good earthing condition  
before using to guarantee your safety.  
1
 
Safety precautions  
When the machine is normally using,  
Please insert the power cord into special  
receptacle with rated voltage. Be sure to  
use single-phase three pins receptacle.  
The earthing terminal of the receptacle  
must be earthed reliably. If possible,  
please adopt electric leakage protector.  
please put the power plug at the  
location easily to be inserted and  
extracted by hand. Be sure to pull the  
plug off when there's power failure, or  
the machine is being moved, cleaned  
or when it is idle.  
Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.  
Keep the pin of the power plug clean, if the power plug is polluted with dust,  
please wipe with dry cloth carefully.  
If the power cord or the power plug is bad, to avoid risk it is required to have  
it replaced by the technicians of our special shop or the after-sale service  
department.  
Do not put the machine at damp  
Do not use water hotter than 50 C .  
place like the bathroom . Never wash  
it with water. Do not place wet laundries  
on the control panel.  
In case the washing machine is installed  
on ground with carpet , do not block the  
ventilation hole with carpet.  
Do not wash water-proof laundries like  
the raincoat, bike covers etc, to avoid  
abnormal vibrations in spinning.  
Ventilation hole at  
the bottom of the  
washing machine  
Do not let the machine share one receptacle  
with other electric appliances. If the power  
plug is damaged, or the plugging into the  
receptacle is loose, do not use the plug any  
more.  
2
 
Safety precautions  
Do not stretch hands into the working  
machine. It is dangerous even if the  
rotation is slow. Take special care of  
the children.  
Do not decompose, repair or alter the  
machine by yourself.  
Do not put any hot or heavy items  
( such as the kettle with hot water )  
on the washing machine.  
Do not wash laundries with volatile  
materials (such as thinner, petrol etc.).  
ol  
tr  
Pe  
ner  
in  
h
T
Handicapped or children without care  
shall not use the machine.  
Keep the machine away from direct  
sunlight and heat source like the  
heater.  
Please keep the lint filter in good condition, and  
install it to proper position during washing. If the  
lint filter is lost or damaged, please contact the local  
after-sale service department of our company.  
Install  
Dismantle  
3
 
Installation and adjustment  
Please install and adjust the machine according to the requirement of the manual. It is  
very important to your security and correct operating the machine.  
Usage of the drain hose  
The drain hose shall drain smoothly  
1.The height of the drain hose shall be  
less than 10cm, or the drainage will not  
be smooth, and cost such long time that  
<10cm  
the machine may stop at mid way.  
2.Do not ramp or press the drain hose.  
3.If the drain hose is too long, cut it at mid  
point. To make smooth drainage, cut the  
front end of the hose slantingly.  
>
30mm  
4.If extra drain hose is needed, please  
make separate purchase. The inner  
diameter of the extra hose shall not  
less than 40mm, and the length shall  
not exceed 1.5m.  
<1.5m  
If the extra hose is too long, cut it  
either at A or at B point.  
A
B
4
 
How to change the direction of the drain hoses  
Figure 1 indicates the ex factory installation  
position of the drain hose.  
Back  
Extend the drain hose from the side of spin tub  
Front  
Figure 1  
Put soft items on the ground. Lean the machine  
down gently with the front surface facing the  
ground. Take off the drain hose from the cabinet.  
Dismantle the drain hose fixing clamp and take  
the hose out of the fixing groove.  
(See to Figure 2).  
Soft item  
Figure 2  
Embed the drain hose into the groove along the side  
of the spin tub in the order of 1 ~ 3 , heading for the  
side of the spin tub. (See to Figure 3).  
Embed the drain hose into the groove with  
hands. Take care not to damage the drain  
hose in fastening the fixing clamp.  
Extend to the  
spin tub side  
Fig ure 3  
Install the water inlet hose; Select the water level  
Insert the water inlet hose into the water-filling  
entrance on the control panel  
To  
dismantle the water inlet pipe, just push the  
control handle as indicated in the figure and  
pull it out  
Water inlet  
hose  
Water-filling  
entrance  
Select water level according to the  
quantity of the laundries.  
Set the water level adjusting lever  
to needed line.  
Water level  
indicator  
Max  
Maximum  
Medium  
Med  
Min  
Minimum  
5
 
Preparation before washing  
Preparation before washing  
1.Connect the water inlet hose.  
2.Confirm that the washing machine is earthed  
reliably . Then insert the power plug into the  
receptacle. Do not connect the earth terminal  
to the gas pipe and tap water pipe.  
3.Put down the drain hose .  
4.Slanting or uneven ground may result in  
unstable working or abnormal noise. Please  
make the machine stand horizontally.  
Pay attention to followings before washing the laundries  
Check if  
The quantity of When the pulsator  
the laundries  
shall not be too buttons of the  
large. Stretch laundries may  
and loosen the cause noise. For  
laundries before the sake of  
Clear the  
Tie the long  
strips; fasten  
the buttons;  
close zippers.  
the laundries  
has special  
requirement  
on washing  
is running , the  
pocket. Take  
out the coins,  
sand, hairpins  
etc.  
putting them in discretion, please  
the tub.  
put the laundries  
with buttons into  
other laundries.  
a. Check if the laundries are applicable for washing with machine.  
b. Divide the laundries that are not colorfast from other laundries.  
c. Put those laundries difficult to absorb water into water with hand.  
d. For those laundries with heavy soil, please first remove the dirt like  
mud or dust. For the parts with heavy soil, please apply detergent on  
them in advance, which can make it easier to remove the soi.l  
e. For those laundries that may get lint ball and those with long fur, turn  
it over before putting in.  
f. Do not put those laundries polluted by chemicals into the washing  
machine directly.  
6
 
The musts in washing  
The capacity of washing and spinning of the  
machine refer to the largest weight of the  
standard laundries under dry condition that can  
be washed or spinned in one time.  
The thickness ,size , type of the cloth will influ-  
ence the actual washing capacity. It is suit-  
able to put in reasonable amount of laundries  
and the laundries can be turned round in wash-  
ing for one time washing.  
It is suggested to use foamless washing  
powder.  
Do not select " Max " water level for  
laundries less 1.5kg , so as to avoid splashing  
of water.  
Usage of the detergent  
How to use the washing powder  
How to use the whitener  
Direct dissolved in the machine:  
1.Fill small quantity of water.  
2.Add the powder . Runfor 30  
seconds to dissolve it completely.  
3.Put it in the laundries. Select suitable  
water level.  
Fill water to decided level. Dilute  
the whitener with container. Pour  
it slowly into the washing tub.  
Avoid using whitener on laun-  
dries with color or pattern as they  
are prone to lose color.  
The instant dissolving of thewashing  
powder:  
1.Prepare warm water of 30C and a  
container.  
2.Add the powder while stirringto fully  
dissolve it.  
The whitener shall not touch  
the laundries directly.  
Refer to the user's manual for  
the usage and quantity of the  
whitener.  
The powder is more proneto pollute the  
laundries than the detergent. Therefore  
please use it with properquantity.  
For powder whitener, please  
dissolve it before using.  
Dosage of different washing powder is  
different. Please refer to the instruction  
of the washing powder for the detail  
dosage.  
7
 
Washing sequence  
Drain switch  
Not set the switch to  
DRAIN during washing  
Spin timer  
Function selector  
Wash timer  
(To set to below 1 minute,  
first set to  
(Soft current,  
Standard current)  
2
minutes then  
(To set to below 2 minutes,  
first set to 6 minutes then  
turn it back.).  
turn it back. it can increase  
the service life of the timer).  
OFF  
OFF  
STANDARD  
STANDARD  
5
4
1
SOFT  
SOFT  
DRAIN  
CALEFACTION  
2
3
(HWM80-0626SH)  
(HWM80-0626S)  
DRAIN SWITCH  
SPIN TIMER  
WASH TIMER  
FUNCTION SELECTOR  
Wash  
1.Water-filling selector  
1 Set the water inlet selector at the "WASH" side.  
(Figure 1)  
2 Set the water level adjusting lever to needed line.  
2. Fill the water and add the dissolved washing  
powder to make the water level reach the preset  
position. (Figure 2)  
WASH  
SPIN  
WATER LET LECTOR  
Figure 1  
Figure 2  
Run washing program for some time to stir and  
dissolve the powder completely.  
STANDARD  
STANDARD  
SOFT  
SOFT  
Page7  
CALEFACTION  
3.Put in the laundries. If the water quantity is  
insufficient, please add water.  
Figure 3  
4.Select the current.  
Select the strength of the current according to  
the laundries. (Figure 3)  
(HWM80-0626S)  
(HWM80-0626SH)  
FUNCTION SELECTOR  
Figure 4  
5.Select the washing time  
Select the washing time according to the laundries.  
(Figure 4)  
WASH TIMER  
OFF  
6.After washing, set the "WASH SELECTOR"  
at "DRAIN". (Figure 5).  
DRAIN  
Figure 5  
DRAIN SWITCH  
8
 
Calefaction  
Function selector  
(Soft current,  
Standard current)  
STANDARD  
SOFT  
CALEFACTION  
Figure 6  
(HWM80-0626SH)  
FUNCTION SELECTOR  
When filling water to MAX or MED and MIN water levels,  
turn the SELECTOR to the CALEFACTION after put in the  
laundries. It begins to heat after close the wash tub, when  
the temperature reaches 45  
5 , the Buzzer will give an  
musical alarm. Then turn the selector to "STANDARD"  
or "SOFT" , the heater will stop heating and the Buzzer  
will stop alarming. It begins to wash after turning the WASH  
TIMER.  
Remarks Don not open the wash tub when heating  
otherwise it will stop heating and influence the heating  
time.  
9
 
Midway spinning  
1.Put the laundries into the spin tub evenly and smoothly.  
2.Spin  
(1) Put the gland in properly.  
Please put in the gland properly even if the  
laundries quantity is small.  
Push  
Gland  
Push  
The laundries  
are slanting  
No gland  
Proper  
Proper  
(2) Close the inner and outer cover of the spin tub.  
Outer cover of  
The spin tub  
Inner cover of  
The spin tub  
(3) Spin for 1-2 minutes.  
3.Run the foam-removing spinning.  
Set the inlet selector handle on spin side and  
1
fill water for about 1 min.  
In case water flows out from wash tub side  
due to too much inflow, please turn down  
the water tap a bit.  
WASH  
SPIN  
WATER NLET LECTOR  
2
Close the spin tub outer cover and spin  
for about 1 - 2 min.  
10  
 
Rinsing  
Rinse with water-filling  
1.Put the laundries into the wash tub. Select  
suitable current according to the laundries.  
2.Adjust the water level  
Set the water level with water level adjusting  
lever according to the laundries quantity.  
Then fill suitable water continuously.  
3.Rinse  
Adjust the wash timer to 5-7 minutes to do  
rinsing.  
(Repeat the midway spinning and rinsing with stored  
water for 2-3 times.)  
Rinse with stored water  
1. Put the laundries into the wash tub. Select suitable current  
according to the laundries.  
2. Fill water to preset water level.  
3. Rinse  
Adjust the wash timer to 2-3 minutes to do rinsing.  
When the laundries quantity is below 4.0 kg, please use  
SOFT current.If you use STANDARD current,  
it may splash.  
11  
 
Spinning  
1.Put the laundries into the spin tub evenly and smoothly.  
2.Press the gland in the tub properly. Close the inner and  
outer cover of the spin tub.  
3.Spin  
Select suitable spin time according to the laundries, and do spinning.  
During spinning, if there is abnormal sound, it is generally owing to  
slanting placement of the laundries. Please stop the machine and  
reorder the laundries.  
In spinning, it will pause the work if you open the outer cover of the  
spin tub. Close it to resume the spinning.  
To do spinning and draining and rinse  
with water-filling together, please first  
do spinning for around 1 minute, then  
do draining or rinse with water-filling .  
Otherwise the spinning will stop owing  
to too much water stored in the spin tub.  
12  
 
Disposal after washing  
After using, please clean the lint and foreign materials of the lint filter and  
overflow filter in time. Otherwise it may influence your using the machine.  
Please first pull off the power plug from the receptacle before cleaning.  
Cleaning the lint filter  
The lint filter must be used during washing.  
It must be cleaned in time after each using.  
1. Press the elastic piece at upper end of lint filter to  
release the tab from the filter cover, and pull the lint  
filter outward to remove it. (See Figure 7).  
Figure 7  
2. Remove lint  
Pull the lower end of lint filter rear cover outward  
Lint filter rear cover  
to disassemble it from the lint filter front cover.  
Remove lint completely with clear water. (See  
Disassemble  
Figure 8).  
Install  
3. Install lint filter  
Lint filter frontcover  
Page 8  
Figure 8  
Cleaning the overflow filter  
Too much lint on the overflow filter will influence  
the normal usage of the machine. Please  
clean it every two months.  
1
Take off the overflow filter.  
Elastic fixing  
claw  
As indicated in the figure, nip the elastic fixing  
claw and pull it to the direction of the arrow to  
take it off.  
13  
 
Cleaning the overflow filter  
2. Take off the corrugation pipe.  
Dismantle the upper part of the  
corrugation pipe inside the  
overflow filter ( as indicated in  
Figure 9).  
Water level  
adjusting lever  
Corrugation  
Pipe  
3. Cleaning the overflow filter  
Clean the lint around the filter  
and flush with tap water.  
Figure 9  
4. Install the overflow filter.  
(1).Install the corrugation pipe.  
(2).Insert the mounting plate at  
the bottom of the filter into  
the valve cover.  
Hook  
(3).Hang up the hook at the left  
upper side.  
(4).Push the upper part in (as  
indicated in Figure 10).  
Figure 10  
Disposal of the complete unit  
After washing, dismount the water inlet  
hose.  
Do not store water in the tub for long  
period. Discharge the water immediately  
after each using.  
Pull off the power plug and hang up the  
power cord.  
Hang up the drain hose.  
Wipe the complete unit with soft  
cloth twisted dry.  
Wipe with neutral detergent if too  
dirty.  
Do not wash it directly by water.  
Wipe off the water drops on the surface  
and inside the tub with clean soft cloth.  
Open the cover of the wash tub and the  
inner/outer cover of the spin tub for  
some time (about one hour), then close  
them.  
Petrol  
Thinner  
Alcohol  
14  
 
Trouble-shooting Answers to question  
If the laundries fall to the outer side of the spin tub  
If the laundries fall to the outer side of the spin tub, Please  
take it out quickly.  
1.Dismantle  
First take two plugs out, then dismantle the two  
screws which fixed the Spin tub frame. As  
indicated in the figure, push the point marked  
with " " to pull the spin tub frame to oblique  
upwards to dismantle it.  
Spin tub frame  
Figure 1  
Spin tub  
Please check carefully. The laundries may fall to the  
lower part of the outer side of the spin tub ( Figure 2).  
If the laundries fall to the outer side of the spin tub,  
during spinning the draining will get blocked and the  
rotation speed of the spin tub is reduced.  
Laundries  
Figure 2  
2.Install  
After install the back edge of the spin tub frame to  
proper position, push the four points marked with  
"
" by force to reset it, fix it with screws, then  
fixed the two plugs at the position.  
Figure 3  
When the remained water is frozen  
Prevent the freezing  
Drain completely after using.  
When the water is frozen  
Below 50  
Pour hot water below 50  
into the wash tub  
to soak it completely. Then turn the pulsator  
with hands gently. Please confirm the drainage  
can work normally before next using.  
15  
 
Trouble-shooting Answers to question  
(If there's breakdown, please pull off the power plug before checking) The following  
phenomena are not breakdowns sometimes. Please confirm again before sending  
it to repair. If there are real breakdowns, please come to the special maintenance  
department or after-sale service department of our company. Do not repair it by yourself.  
Phenomena  
The reason  
Is there power failure?  
The machine does  
not act.  
Is the power plug loose?  
Is the pulsator twisted by foreign materials?  
Does the drain hose put down?  
Is the drain hose frozen?  
The draining does  
not work.  
Is the drain hose blocked by foreign material?  
Are there laundries falling to the outer side of  
the spin tub?  
There's abnormal  
sound during  
washing  
Are there hair pin, coins or metal items brought  
inside the tub?  
Is the machine slanting?  
There's abnormal  
sound and violent  
vibration during  
spinning  
Is the gland pressed evenly?  
Are there laundries falling to the outer side of  
the spin tub?  
Are the laundries in spin tub too much?  
There may be some  
waterflowing out of  
the drain hose in the  
first use of the  
It is the water remained in the factory inspection  
of performance.  
machine.  
16  
 
Packing list  
Name  
Quantity  
User's manual  
One piece  
Warranty card  
Water inlet hose  
One piece  
One piece  
One piece  
One set  
Gland  
Twin-tub washing machine  
Specification  
Water level / Water  
quantity (about)(L)  
Maximum/71 Medium/60 Minimum/49  
Injection pressure(MPa)  
0.02 0.2  
8.0/6.0  
Rated washing / spinning  
capacity kg  
17  
 

Graco Battery Charger 309502G User Manual
Gravely Lawn Mower 39000 User Manual
Haier Freezer BD 478A User Manual
Heatcraft Refrigeration Products Fan BN ETPTB User Manual
Hotpoint Washer AQ113DA 697 E User Manual
Huawei Car Video System VP9050 User Manual
Hunter Fan Fan Type 5 Models User Manual
Husqvarna Lawn Mower 16 H User Manual
Hypertec Mouse KYBAC100 00BEIHY BEIGE User Manual
Imation Network Card Hard Disk Storage System User Manual